产品介绍
Ⅰ. Product specifications (simple)
1. Technical overview
The solar water circulation device uses a new renewable energy source, solar energy, to continuously recycle water that is not easily recycled, such as rivers and lakes, and provides abundant oxygen to the bottom layer with low dissolved oxygen concentration to achieve clean water quality and become an environmentally friendly product of healthy water ecosystem. .
2. Equipment specifications
Dimensions (without buoyancy material) : Diameter 2,725±10mm, height 2,017±10mm
Dimensions (including buoyancy materials): diameter 6,500±10mm, height 2,017±10mm, 650kg
3. Traffic
SLVー2000 (2,046 m3/hr)
4. Material and specifications of main components
Distinguish | Project | Material | Specification | Quantity |
1 | PV panel | Mono type | 195W, 1580X808X40, 15.5kg | 3 |
2 | Battery | Pb battery | 12V, 200Ah | 2 |
3 | Controller | PCB、aluminum | MPPT, DCDC convert, Main digital controller | 1 |
4 | Motor | Cover: aluminum | BLDC, 120W, 5.9kg | 1 |
5 | Impeller | SUS304 | diameter 750mm, 2 knife | 1 |
6 | Disc dispenser(dish) | SUS304 | diameter 1758mm, height 183mm | 1 |
7 | Suction pipe (hose) | PE tarpaulin | diameter 900mm, length5000mm | 1 |
8 | Float | HDPE | diameter 600mm, height 220mm | 27 |
9 | Fixed part (anchor：Anchor) | HDPE Concrete | 40kg | 2 |
10 | Turn buckle | coupler :HSB Round bar : SUS 304 | SCREW-R/L, PIPE, SOCKET-R/L | 3 |
5. Maintenance tool
5.1 Spanner
Items | Specification | Quantity | Remarks |
Spanner | 10mm ~ 24mm | 2ea |
5.2 Wrench
Items | Specification | Quantity | Remarks |
六角形(Wrench) | 2.5mm ~ 12mm | 1ea |
5.3 Driver
Items | Specification | Quantity | Remarks |
Driver | Cross | 1ea |
Ⅱ. Related Matters
1.General matter
1.1 Scope of application
1.1.1 This specification is a solar water circulating water device used to remove harmful algae and increase dissolved oxygen concentration in rivers and lakes.
Specification content.
1.1.2 Main content
(1) Installation method: direct installation in the water system, floating mode, anchor pier, fixed chain (Chain Attachment)
(2) Water circulation devices using solar energy: solar panels (PV panels), BLDC motors (brushless DC motors), impellers, digital controllers, batteries, etc.
(3) Floating system: wave-resistant HDPE (high-density polyethylene) buoyancy material
1.2 Main specifications
1.2.1 Dimensions and weight: Dimensions (without buoyancy material): Diameter 2,725mm, Height 2,017mm, Dimensions (including buoyancy material) Diameter 6,500mm, Height 2,017mm, 650kg;
1.2.2 Main components: STS304, HDPE (high density polyethylene)
1.2.3 Flow Rate: SLV-2000 (2,046 m3/hr)
1.2.4 Installation depth: 1.0 ~ 30 M
1.2.5 Drive mode: It adopts independent power drive mode of solar concentrating and battery. (Solar battery module: 195Watt × 3sets, charging battery: 200Ah × 2sets)
1.2.6 Control mode: Mppt (maximum power point tracking) mode adjusts the number of rotations of the BLDC battery according to the battery voltage.
2. Main parts details
2.1 Solar Module
2.1.1 The solar cell module converts solar energy into electrical energy, and collects the built-in battery by collecting light to drive the mechanical motor.
2.1.2 There are three solar cell modules, arranged in a triangle. One solar cell module is 195 watts. According to the dimensions and season of the installation area
Factors should be adjusted to be able to accept the most direct sunlight.
2.1.3 There should be additional accessories for the prevention of bird intrusion in the upper part of the solar cell module.
2.2 Built-in battery
2.2.1 The built-in battery is capable of charging the amount of electricity produced by the solar module during the day. Different from using the device for a long time, it can quickly reduce the battery performance and make
The existing battery with a long life is a solar-powered battery that can be used at night and on cloudy days.
2.2.2 In order to improve work efficiency and extend service life, the built-in battery should be installed in stainless steel that can solve the risk of electric leakage caused by direct light and moisture.
(SUS304) inside the outer casing.
2.2.3 In order to prevent the occurrence of fire, cut off the risk factor, a separate low-voltage valve is used, which can reduce the internally generated gas to electrolysis.
The liquid, and the internal gas is discharged outward to solve the high pressure when a fire occurs inside the product.
2.2.4 A high-rigidity special electrolytic cell (RPP) with impact resistance and high temperature resistance is used. Product damage caused by liquid leakage and environmental damage
For damage to the product, a 3-fold closed structure shall be used.
2.2.5 The wires connected to the built-in battery should be of anti-corrosion and anti-rust structure.
2.3 Digital Controller
2.3.1 The digital controller is installed in the corner around the solar cell module and is firmly fixed by bolts.
2.3.2 It should be composed of water-resistant and waterproof NEMA 4X. It is equipped with a connector for connecting the solar cell module in front, and a motor is connected to the side.
Battery, operating status indicator and switch.
2.3.3 The switch will send the command signal of the on/off mechanism. When it is turned on, it will be turned to the inside direction and turned to the head. When it is closed, it will be turned to the outside direction to stop the machine.
Device.
2.3.4 The digital controller can automatically control the solar voltage, current, battery voltage and commands to start the motor. This digital controller should be installed
There is a memory that stores the above data.
2.4 Motor Controller
2.4.1 Motor controllers and motors should be installed close to each other due to frequent exchange of information.
2.4.2 Wires with starter motors shall be used for sealing treatment. Receive signals and power from the digital controller.
2.4.3 Wires connected to the motor controller shall be treated with corrosion and rust.
2.5 Motor and impeller
2.5.1 The motor should be installed under the Top Plate and firmly connected to the aluminum motor cover and bolts.
2.5.2 Using brushless type, the noise is not high when starting the motor, and the rotation is smooth. A fixed motor is used.
2.5.3 Use a coupling to connect the impeller and shaft below the motor.
2.5.4 The impeller is made of stainless steel. A stainless steel flag indicator with a prompt start state and a rotation speed is installed.
2.5.5 The direction of rotation of the impeller is clockwise.
2.5.6 The impeller is made of stainless steel (STS304) and fixed to the shaft. Should be able to pump up from the bottom.
2.6 dish dispenser
2.6.1 The disc-shaped distributor is equipped with an impeller that can pump the bottom water up and discharge it to the four sides. Made of water-resistant stainless steel (STS304). for
The impeller is located in the center of the distributor and should have sufficient space.
2.6.2 In order to achieve optimum water flow, the dish distributor shall be installed at a position of 5 to 6 cm below the water meter. To form a water layer in the square, above the dish distributor
A sleeve (Sleeve) is mounted laterally. In order to adjust the vertical height with the water meter, the appropriate position should be marked according to the model of the chain bracket.
Use a sleeve nut.
2.6.3 A suction pipe that draws water from the bottom is fixed under the dish-shaped distributor.
2.7 Suction tube and suction tube bracket
2.7.1 The suction pipe is used to extract the bottom water and is connected to the lower part of the dish distributor. The material is PE tarpaulin.
2.7.2 The length of the suction pipe can be used in the 1.5 to 5.0 m water layer. The diameter should be 80cm or more. Should be connected for the purpose of use, adjustable length
Chain (notchChain Bracket) with a U-shaped groove.
2.7.3 The length of the suction tube should be adjusted without the use of any tools. In addition, there should be an indication of the length of the display.
2.7.4 The end of the suction pipe shall have a suction pipe bracket that prevents the inflow of sediment into the bottom layer. In shallow water without suction pipe, the suction pipe bracket should be fixed
Below the dish divider.
2.8 Buoyant material and buoyant material bracket
2.8.1 is a structure that floats the solar water circulation device on the water meter, made of HDPE (foam filled high density polyethylene) buoyancy material, fixed and supported
The scaffolding composition of the buoyant material.
2.8.2 The buoyant material bracket is made of stainless steel (STS304) and is fitted with a sleeve nut that adjusts the height of the disc distributor.
2.8.3 The buoyancy material is made of high-density polyethylene (HDPE) and is laminated to provide sufficient buoyancy.
2.8.4 In order not to affect the flow of water discharged from the dish distributor, a spherical buoyancy material is used. In addition, in order to achieve the ultimate resistance to wind resistance, prevent intentionality
Damage will minimize the contact area, and the area from the water meter should be minimized.
2.8.5 In order to reduce the sloshing of the device caused by the waves, a wave-resistant buoyancy material that is optimized for performance and efficiency is used.
2.9 Anchoring (fixed)
2.9.1 In order to prevent the loss and damage of the solar water circulation device caused by the water flow, it is installed in one of the following two ways.
(1) Mooring Block is attached to the bottom of the water system and fixed. Connect two mooring anchors in series, made of high density polyethylene
(HDPE). The interior is filled with concrete and weighs approximately 40kg. The chain connecting the solar water circulation device and the mooring anchor should be longer than the water depth by 2~
3 times.
(2) Fixed by using the duckbill anchor and chain on land.
It is a method used in the case where the water system is narrow or the mooring anchor cannot be installed. Install two duckbill anchors on both sides of the water system, and anchor the two duckbill chains
The connection is then fixed in the middle of the chain with a short chain of buoyant material.
previous item: Scenery water heater
关闭返回